Safety wiring oil filters, oil temperature sensors, and other items works on the same general principle. The connection to the next bolt should likewise pull in the direction of tightening the bolt. Safety wire should always be wrapped around the head of a bolt in a direction that would tend to tighten the bolt in other words turn it clockwise as viewed from the head of the bolt. Since safety wire techniques were well-covered in a September 2015 KITPLANES article and in AC 43.13-1B, I will not repeat that material here, except for a few brief comments. 041-inch wire, but verify that with your propeller manufacturer before you buy it. Be patient and practice a few times until you get it right. 041-inch wire for anything after you have worked with it. However, if you must use safety wire there is a good illustration of approved methods in AC43.13.īest practices say that you should use the prescribed size safety wire for your job, but you will be sorely tempted to avoid. If possible it is much more convenient to use turnbuckles that work with clips rather than safety wire. 041-inch wire, as do most turnbuckles, except for very large ones that few amateur builders will ever encounter. Larger wire is generally used for bolts sized AN8 or larger and turnbuckles. Smaller wire is typically used to secure screw sizes 8-32 or smaller. 051 inch, but amateur builders will mostly use. Stainless steel wire comes in diameters ranging from. Safety wire comes in stainless steel, brass, and aluminum, but most amateur airplane builders will only use stainless steel wire for their projects. 020-inch safety wire unless you need it for something else. This unit is not usually serviced by someone in the field, so there is no reason to buy. Small screws such as these found on a fuel distributor are typically secured with. Look in Section 7 for more information on safety wiring. By the way, the digitally inclined can also find AC43.13-1B online for free. It would be hard for anyone to take you seriously as an airplane builder if you have never cracked open this book. If you are using best practices, you already have this book, but if you don’t, you should get it. Whenever you have a safety wire project in front of you, it is a good idea to look up the proper procedure there. Safety WireĪC43.13-1B goes into great detail on how to safety wire various nuts, bolts, screws, hose fittings, turnbuckles, and just about anything else you can imagine safety wiring. Never substitute a stop nut for a castle nut and cotter pin at joints where fully tightening the nut would stop the joint from rotating. For firewall-forward installations don’t forget to use AN363 all-metal stop nuts if you decide to go that way. Their vast experience with this arrangement makes it hard to argue against it, recommendations of AC43.13-1B notwithstanding. The concept of forcing rotation into the rod end rather than around the bolt underlies Van’s recommendation to use standard AN365 nylon insert stop nuts at most rotation joints such as aileron hinges and control push/pull tubes. Verify the correct size with your propeller manufacturer. 032-inch, but with practice a neat job is possible. This larger wire is harder to work with than. The recommended fix was to dab some epoxy or JB Weld on the cotter pin tail so it couldn’t be pulled loose. This RV-4 brake pedal is subject to a service bulletin because the cotter pin nearest the pedal face often got caught on the pilot’s shoe. A recent EAA Hints for Homebuilders video highlighted this method. An alternate method of protecting the tails of a cotter pin is to orient the pin sideways and turn the tails into slots adjacent to the one through which the pin lies. This issue came up with the rudder pedals for RV-4s and resulted in a service bulletin. JB Weld or a similar product will also work. If the tail of a cotter pin sticks out in such a way that it may snag on shoes or clothing, it may be necessary to put some epoxy over the tail of the pin to keep it in place. Sometimes changing a washer from thick to thin will help get proper alignment. This is generally allowed unless specifications say otherwise. The nut may need to be overtightened a bit to achieve the proper alignment. When using a castle nut, the slot of the nut needs to be lined up with the hole in the bolt. For convenience cotter pins are usually longer than needed and then cut off. This idea was suggested by an EAA member in a Hints for Homebuilders video.Ī properly installed cotter pin will be 1/64-inch smaller in diameter than the hole in the shank of the bolt and will be long enough so that when it is bent over, it will extend at least to the center of the bolt or clevis pin. This alternative method of securing a cotter pin works well when there is poor access to the top of the nut or where snagging of the cotter pin is a concern.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |